|
#1
16-11-2004, 09:41
|
|||
|
|||
|
VIA Solder Removal
I made a mistake with two via's on the back of my board. I've tried to remove it with desoldering braid with no luck. Is there anything small enough to get into the vias to force the solder out ? I need to get these vias cleaned out in order for the chip to work. The install of my Matrix Infinity chip is complete except I get a black screen and i'm sure its because of the two vias that have solder in them that shouldnt
 Thanks for your help! 
|
| Sponsored Links |
|
#2
16-11-2004, 11:36
|
||||
|
||||
|
It shouldn't make a difference filled or not.
Check the BIOS points.
__________________
[SIZE=3][COLOR=orange][B][COLOR=blue]PS2, [/COLOR][COLOR=yellowgreen]XBOX[/COLOR] & [COLOR=darkolivegreen]Xbox 360[/COLOR] installs / repairs in [U][COLOR=red]West Yorkshire,[/COLOR][COLOR=red] UK[/COLOR][/U] - [COLOR=#ff0000]Nationwide Service [/COLOR][COLOR=darkorange]-[/COLOR]Please Contact me by PM for more info[/B][/COLOR][/SIZE] :) [B][SIZE=4][COLOR=#ff0000][COLOR=seagreen]360 DVD Drive Fw.[/COLOR] [COLOR=orange]Upgraded/Recovered/Restored -[/COLOR] Bad Flash? No Problem! [COLOR=blue]PM for info[/COLOR][/COLOR][/SIZE][/B] [B][SIZE=4][COLOR=#ff0000][COLOR=yellowgreen]XBOX 360[/COLOR] [COLOR=blue]v1.0[/COLOR] [COLOR=blue]- [/COLOR][/COLOR][COLOR=red]Samsung TS-H943A [COLOR=orange]w/ iXtreme 1.4 Fw.[/COLOR] :D [/COLOR][/SIZE][/B]
|
|
#3
16-11-2004, 16:46
|
|||
|
|||
|
Ok, now I double checked my connections and now it plays my original ps2 dvd fine and I get the Infinity logo 1.35 when it boots. It will not boot any backups I get the Red Screen. I had this problem on another install with my wires being wrong but i've double checked all my connections on this install and can't seem to see anything wrong.
What causes the Red Screen?
|
|
#4
17-11-2004, 06:11
|
||||
|
||||
re
yes wont make a diffrence if the vias are filled or not once they are not bridgeing anything does is have to go the the browser screen when loading as if it does then the laser is week and this messes with the boot pro also what size wire did u use? will it boot ps1 backups/ps2 cd-r backups look over the vias u soldered to and the bios chip legs and see if all the wires are atached well
hpes it helps
__________________
1800 AMD 1027 ddr Pioneer DVR-A07 the university of limerick chipper ps2 v10 pal+ripper2 gold (new baby) ps2 v6 pal+duo chipped by me Don’t take life too serious you’ll never get out alive!
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| *sigh* No solder mod chip question.. | DRob | PS2 Games | 7 | 04-03-2003 17:44 |
| Anyone had problems with : PS2 No Solder Mod Chip Version 4? | Jon_Adams | PS2 Games | 2 | 25-02-2003 18:30 |
| no solder mod v5/6 question on loading dvd-r's | la_eternal | PS2 Games | 2 | 28-05-2002 15:48 |
| no solder RUNS DVD as well! legit or no? | GmRunner | PS2 Games | 3 | 01-05-2002 06:55 |
| Mod-Chip Solder . . . | pSyCo | PSX Games | 3 | 05-12-2000 01:10 |
Linear Mode
