|
#1
08-08-2004, 16:52
|
|||
|
|||
|
Anyone soldered a neo12 to a ver 9? Help!
Hi, I'm a noobie and couldn't find any info on a search so I thought I'd post. I bought the chip and kit- Neo 12 for ver. 9 PS2 silver.
Can't figure the diagram as there seems to be 21 solder points and it only requires a 12 wire solder. Could someone explain to me please. I'm a virgin at this caper.  This is the diagram here : www.mod-chip.com/images/neo12_v9.jpg and where does the two yellow wires go ? Ground and....positive? Thanks awfully  Teresa 
|
| Sponsored Links |
|
#2
08-08-2004, 17:44
|
||||
|
||||
|
Unfortunately Teresa,
it seems youve had the wool pulled over your eyes. Even though the Neo12 (really isnt even a real "Neo" chip) claims to only require 12 or so wires to solder. They dont tell you that you still actually need to solder 21 or so "points". Basically the other points are just bridges that you must make with solder. Also that chip is basically a crap chip. Your best bet would have been to buy a Duo2. Tyler!
__________________
[B]V7 Ps2 Messiah 2 V13 PSTwo DMS4 Pro and HD-Connect(Installed myself)[/B]
|
|
#3
08-08-2004, 18:17
|
|||
|
|||
|
Thanks Tyler - I think - which ones' are the points on the diagram? I understand the diagram even less so now. Has anyone a photo of the completed job
I was recommended this chip too 
|
|
#4
08-08-2004, 18:55
|
||||
|
||||
|
In that link you posted it shows where you need to place the chip to bridge it. Basically all you do is drag solder to the points.
Who recommended this chip? I would be upset with them. Go to our Ultimate Info Sticky and check out the Duo2 Review. Tyler!
__________________
[B]V7 Ps2 Messiah 2 V13 PSTwo DMS4 Pro and HD-Connect(Installed myself)[/B]
|
|
#5
08-08-2004, 19:11
|
||||
|
||||
|
Quote:
LOL http://story.news.yahoo.com/news?tm...us/bodies_found
__________________
"[B]I am Neptoon king of the sea; I sink ships and conger up storms[/B]" -Me
|
|
#6
09-08-2004, 18:26
|
||||
|
||||
|
@ eejit mk1
Check your PM
__________________
[SIZE=3][COLOR=orange][B][COLOR=blue]PS2, [/COLOR][COLOR=yellowgreen]XBOX[/COLOR] & [COLOR=darkolivegreen]Xbox 360[/COLOR] installs / repairs in [U][COLOR=red]West Yorkshire,[/COLOR][COLOR=red] UK[/COLOR][/U] - [COLOR=#ff0000]Nationwide Service [/COLOR][COLOR=darkorange]-[/COLOR]Please Contact me by PM for more info[/B][/COLOR][/SIZE] :) [B][SIZE=4][COLOR=#ff0000][COLOR=seagreen]360 DVD Drive Fw.[/COLOR] [COLOR=orange]Upgraded/Recovered/Restored -[/COLOR] Bad Flash? No Problem! [COLOR=blue]PM for info[/COLOR][/COLOR][/SIZE][/B] [B][SIZE=4][COLOR=#ff0000][COLOR=yellowgreen]XBOX 360[/COLOR] [COLOR=blue]v1.0[/COLOR] [COLOR=blue]- [/COLOR][/COLOR][COLOR=red]Samsung TS-H943A [COLOR=orange]w/ iXtreme 1.4 Fw.[/COLOR] :D [/COLOR][/SIZE][/B]
|
|
#7
10-08-2004, 15:34
|
|||
|
|||
|
Getting there......not....
Well, after much conceptualizing I "think" I managed to work out the illustration: Feel free to patronize me if I'm wrong guys......
Solder chip to board using wiring "front of PS2 board" : A, S, VCC (thick yellow wire), Z, RST (thick yellow wire), R, W. {7 solder points} Solder chip to board using wiring "back of PS2 board" : F,B,G,H, I. {5 solder points} This is the 12 wires they refer to in their advertising blurb. Am I right so far  Next is the bit "pre-soldered pads" P,O,N,M, GND, and Q,T,U,V. {9 in total}. This makes 21 solder bits in total. Is that the correct methodology? I still can't get a satisfactory thought from my brain cube as to how the hell these "pads" connect. Does an idiot heat the pre-soldered pad and stick a bit of wire to it to effect the joint between mobo and chip or is the pre- soldered pad heated to the board directly via some dark necromancy - surely not Harry? Only the deftest (daftest??) would do that  In a word....HELP! Teresa
|
|
#9
10-08-2004, 16:24
|
||||
|
||||
|
well as far as the modchip goes its lame! what i would do is scrap this chip. If you need a chip go on www.mrmodchips.com and get a matrix infinity or dms3 as these are the most reliable modchips avaliable as well as the duo 2 v reliable 2
__________________
[COLOR=Black][B]if it isnt broke dont fix it![/B] [B]www.consoleupgrades.co.uk For All your console needs[/B] [COLOR=RoyalBlue][B]UK'S No.1 I.C.E [URL=www.audiorebel.co.uk]www.audiorebel.co.uk[/URL][/B][/COLOR] [/COLOR][COLOR=DarkSlateBlue][/COLOR] [COLOR=Black][B][/B][/COLOR][COLOR=DarkSlateBlue][/COLOR]
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| ive never soldered before | russellian | PS2 Games | 7 | 29-01-2004 23:54 |
Linear Mode
