FINALLY: I'm getting an XBOX..now what?

[Neipas02]

Welp.. If you're limiting your choices to those two i'd go with the X3.. A lot of guys on here waited for its release to mod their boxes..

This is a quote from an installer from this site
http://www.copying-xbox-games.com/tu...ialid=00000027

I recommend 30 watts at the absolute maximum. Most people use low wattage irons in the 15 to 20 watt range. I have always used 30 watt irons, and while the iron may be just a bit too hot, it seems to work great for me. Also, you want to make sure that your soldering iron has a fine tip point. I think the finer the tip the better. My low watt, fine-tip, soldering iron was about $10. As for solder, I use .022 diameter radio shack solder. It is silver bearing solder, with a Rosin core (62/36/2). You can buy a 1.5 oz spool for about $2 at Radio shack

Hope that helps.. Doesn't really specify the tip but I think if it looks too big it probably is.. Keep in mind that you're working with small solder points.

[Neipas02]

Sorry for the double post but this is a much better link than the previous one.

http://www.chipzone.com/installation/soldertips.cfm

This guy has specifics on everything including prep.

A few of those like the thicker strander wire apply to PS2 chips.

15 watt soldering iron with fine tip
0.10 mm solder tip (this is very small)
30 or 35 awg kynar or similar wire
Thicker stranded wire for 3.3v, 5v and GROUND: 22 awg or similar
flux paste to help soldering
De-solder braid
A safety razor blade & Blue Tack to hold the blade in place
toothbrush

Read the page for more info, hope that helps

[ajmi982]

MAYBE i should just go SolderLESS and use the new XAdapt3r from TeamXecuter when it finally gets sold at Divineo. Then I can just snap it all into place, my xbox wont be gettin moved around anyway and they say they have a win win solution for all versions of XBOX including v1.6 for their X3 to make it solderLESS.

www.teamxecuter.com

think that will be ok? (the cost of the adapter will prolly be the same cost of getting flux, iron, de-solder.....)

[Neipas02]

Bahahah now you're starting to second guess your steady hand skills eh.
Whatever floats your boat dude, I would never TELL someone to get something just suggest. Hopefully 1.6 solderless adapters are reliable. No one knows yet. But if you're a little unsure about your soldering skillz wait for the solderless. All personal preference bud.

[ajmi982]

im relatively confident, its just I would have to spend 20 or so to get the materials, that 20 can go to the adapter. plus i screw up the xbox there goes 150 bux.


what is the likelihood of completely ruining the xbox anyway.?

[Neipas02]

This is true.. Considering it'd be your first go at it, it's possible.. it's my belief that screwing a PS2 is far more likely. With the xbox I guess a good way to kill it would be the result of carelessness or nervousness.. if you let the iron sit on the board too long it could heat up and blow a part.. and if you read the directions wrong you could do some damage by wiring wrong.. there's a spot on the LPC that isn't supposed to have a pin installed... So you have to remove it from the pin header.. With an adapter I would assume they'd have taken care of that for you.

All in all i'd say you made a good choice.. Just make sure everything is secure when you slap the chip on. If you have any loose connections you'll get a FRAG and have to check your setup.. This is more of a point of importance with wiring and soldering since obviously there is more room for error.. And the solderless install is supposed to take away that headache.

[ajmi982]

Yeah, i just dont know if that adapter is available for purchase yet


does anyone know?