|
#1
06-02-2004, 20:07
|
|||
|
|||
magic V help needed for a ver5 ps2
here is a pic of the work i did.
i tripple checked everything with a multimeter and check for shorts. this is what the chip does it boots ps1 orignals and copies it plays movies it will boot a ps2 original games only if i hold the reset button down log enough to disable the chip. it will not boot ps2 oringals or copies cd or dvd. it will not boot imports. i got the chip at easybuy2000. there is no sticker on the chip saying what ver of ps2 it is for. i hope they sent the right one?? i hope someone can help me thanks 
Last edited by acem77; 07-02-2004 at 06:14. 
|
| Sponsored Links |
|
#2
06-02-2004, 20:09
|
||||
|
||||
|
WTF man.. you have a question?
__________________
[COLOR=DarkGreen]PS2 v5/Crystal chip and 15hacked firmware[/COLOR] [COLOR=DarkSlateGray]Halo le.. X3, X3 proswitch, XLCD,2 usb ports, Green controller ports [/COLOR]--->[SIZE=5][COLOR=Red]FOR SALE!![/SIZE][/COLOR] [COLOR=DarkGreen]V1.0, X3, XLCD, proswitch, blue lights all over[/COLOR]
|
|
#3
06-02-2004, 22:38
|
||||
|
||||
|
What version ps2 is this out of? If you are not sure, post your model number.
__________________
[B]may the best of your past, be the worst of your future......:cool: ....[/B]
|
|
#4
06-02-2004, 23:35
|
||||
|
||||
|
The first thing I would tell you to do would be to move that chip off the ground plane! Where you have it the heat/RF shield I'm sure could be shorting out those pads on the chip its self. It’s obviously on a V5/V6 board. If there was no sticker on the chip you have the right chip most likely. The install looks pretty good other then where you put the chip. If you have a continuity checker check point T and the pad right next to it, it looks like there is a bridge....might just be the picture though. Do all that first then get back to use. There is more that could be the problem.
__________________
[color=blue][size=2][b]Click[url=http://www.ps2-scene.org/forums/showthread.php?t=25770] here [/url]to view refes. Click[url=http://www.norcalmods.com/gallery] here [/url]to view install gallery[/b][/size][/color] [size=2][b][color=red]Mod chip installs and repair [/color][/b][/size] [url]www.norcalmods.com[/url] Last edited by spedmetal; 07-02-2004 at 00:46.
|
|
#5
06-02-2004, 23:36
|
||||
|
||||
|
By the way ....what kind of camera are you useing that is AWESOME picture quality.
__________________
[color=blue][size=2][b]Click[url=http://www.ps2-scene.org/forums/showthread.php?t=25770] here [/url]to view refes. Click[url=http://www.norcalmods.com/gallery] here [/url]to view install gallery[/b][/size][/color] [size=2][b][color=red]Mod chip installs and repair [/color][/b][/size] [url]www.norcalmods.com[/url]
|
|
#6
06-02-2004, 23:45
|
||||
|
||||
|
One other thing that looks funny but I cant quite tell is, it looks like you have the Y wire going to V and V going to Y...... am I correct?
EDIT nope I'm wrong V is right , but I cant tell where Y is going it looks like its looping to the back with the rest of the wires on the back when Y is on the top of the board....??
__________________
[color=blue][size=2][b]Click[url=http://www.ps2-scene.org/forums/showthread.php?t=25770] here [/url]to view refes. Click[url=http://www.norcalmods.com/gallery] here [/url]to view install gallery[/b][/size][/color] [size=2][b][color=red]Mod chip installs and repair [/color][/b][/size] [url]www.norcalmods.com[/url] Last edited by spedmetal; 07-02-2004 at 00:47.
|
|
#7
07-02-2004, 06:40
|
|||
|
|||
|
the camera is a sony cyber shot dsc-s70 3MP.
y is at the top by the gnd. when it is all together i put tap on the open contacts. i even tried tuning the ps2 on with just the dvdrom and the chip in the air to see if RF noise was messing with the chip. i checked the t point with my meter again all is good.
|
 |
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Linear Mode
