#1
|
|||
|
|||
Write Error
I have an NEC DVD-RW 1300A. Used CloneDVD and DVDXCopy platinum to try and burn a copy of my video. Small video - about 3G - well under the 4+ GbLimit. (Have AnyDVD 3.2.0.1 running as well)
I get the write error "writing to Video DVD was not successful: DVD write error ( WriteDVD9) A DVD write error has occurred, probably caused by bad medium. Please replace the medium and try again." or "UDF 5 65536" I have tried, Pine, TDK & Imation - all with the same error. However, if I just write Data to the DVD, I can write 4.6GB to any of these DVD's. Any suggestions?? TIA |
Sponsored Links |
#2
|
||||
|
||||
Is your burner set as master? Does the error come up immediately when you try to burn?
__________________
[size=3][color=red][b]Retired[/size][/b][/color] [size=2][color=blue][b] US V7 PS2 w/ Apple Pro Pioneer DVR-112D LG GCC-4480B 48X24X48X16 CD-RW/DVD-ROM Combo[/color][/b][/size] |
#3
|
|||
|
|||
It's set up as a secondary slave with a Reg CD player as secondary master.
It burns about 1/4 of the DVD, then craps out - same place everytime, any kind of DVD. |
#4
|
||||
|
||||
Switch your cd-rom and dvd burner. Your burner should be master. Report back your results with this new setup.
__________________
[size=3][color=red][b]Retired[/size][/b][/color] [size=2][color=blue][b] US V7 PS2 w/ Apple Pro Pioneer DVR-112D LG GCC-4480B 48X24X48X16 CD-RW/DVD-ROM Combo[/color][/b][/size] |
#5
|
|||
|
|||
i have the same dvd writer, and am having the same problem - how do you see if the dvd writer is set as master, and how do you change it?
__________________
Thanks rjlg |
#6
|
|||
|
|||
that must have been it - I switched the drives and have made 2 perfectly good DVD's - thanks so much!!!!
If this is the case, why wouldn't "they" have built the PC this way - geesh. |
#7
|
|||
|
|||
Your bios settings should tell you what is master and what is slave - then you can swap the cables and/or jumpers if necessary.
While I was at it, I also updated the firmware from 1.05 to 1.08. HTH |
#8
|
||||
|
||||
Your very welcome. Don't know why they would set a cd-rom as master and the burner as slave. DVD burner manufacturers even recommend setting it as master when installing.
__________________
[size=3][color=red][b]Retired[/size][/b][/color] [size=2][color=blue][b] US V7 PS2 w/ Apple Pro Pioneer DVR-112D LG GCC-4480B 48X24X48X16 CD-RW/DVD-ROM Combo[/color][/b][/size] |
#9
|
|||
|
|||
That can't be the problem with my dvd writer - it's already set up as the secondary master.
Thanks anyway!
__________________
Thanks rjlg |
#10
|
|||
|
|||
you might want to upgrade the bios while you are at it, I upgraded from 1.05 to 1.08 - that might help
|
#11
|
|||
|
|||
Did that - works fine now!
Thank You!
__________________
Thanks rjlg Last edited by rjlg; 16-01-2004 at 14:58. |
#12
|
|||
|
|||
Excellent - very good news - you're very welcome
|
Thread Tools | |
Display Modes | |
|
|