Cant Turn My Modded Pstwo(slim) On

[lufcfan]

Hmm. Maybe try the adapter first.

If that doesn't work, it could be a problem with the install. Just a quick question though, you haven't had any storms etc over the last week have you? They tend to fry things like this (I found that out the hard way once)

[ran65]

Originally Posted by lufcfan

Hmm. Maybe try the adapter first.

If that doesn't work, it could be a problem with the install. Just a quick question though, you haven't had any storms etc over the last week have you? They tend to fry things like this (I found that out the hard way once)

I - When you say adapter I Assume you mean the adaptor i connected to the cord (not the universal adapter that came with the PStwo) - I`m sure its not the prombem, you see i use three diffrent cords (two of them without adapter) and got the same results.

II - No storms lately (we dont get much off those here in israel), and even if there was one (if i was sleeping??) the PStwo is not connected, why would it, it doesnt work....

Gotta be some else......

[lufcfan]

Then I'd say it's either a loose wire which is grounding something, or something has blown on the mobo somewhere

[ran65]

Originally Posted by lufcfan

Then I'd say it's either a loose wire which is grounding something, or something has blown on the mobo somewhere

Well....First of all thank you for your help but i dont believe this is the problem again:

First of all I checked The chip in the lab where i had it installed and it worked.
Second......Well there is no secend, This aply to the motherboard as well...

[XxCrashxX]

yeah sounds like a loose solder joint
have you opened it up and checked all your solder points with a magnifying glass

[spedmetal]

It sounds to me like it might be a PIC fix problem. You mentioned that he installed a laser fix, do you know which one? If it’s the PIC fix (weather or not it has the diode fix as well) this might be your problem. If the PIC fix detects a problem with the mechacon crashing it will turn your v12 off within 3 seconds. I have also seen the PIC fix turn off the v12's with out even turning them on, much like what you are describing, you tap reset on the v12 and you see the light flash then go back to red again. This is exactly what the PIC fix is designed to do. If the mechacon crashes (which it can do right from standby as well) the PIC fix will shut your v12 down so it won’t fry the laser. There are other things that can contribute to the PIC fix shutting your unit down. If the install is faulty the PIC can act the same way. If the resistance value on the 'J' line is too low the PIC will shut down right from the get go as well. But you don’t want it to be too high or the PIC fix won’t do its job. The value needs to be just high enough to turn on the v12 with out error.

I would suggest you contact the installer of your v12 and let him know your problem.

[ran65]

Originally Posted by spedmetal

It sounds to me like it might be a PIC fix problem. You mentioned that he installed a laser fix, do you know which one? If it’s the PIC fix (weather or not it has the diode fix as well) this might be your problem. If the PIC fix detects a problem with the mechacon crashing it will turn your v12 off within 3 seconds. I have also seen the PIC fix turn off the v12's with out even turning them on, much like what you are describing, you tap reset on the v12 and you see the light flash then go back to red again. This is exactly what the PIC fix is designed to do. If the mechacon crashes (which it can do right from standby as well) the PIC fix will shut your v12 down so it won’t fry the laser. There are other things that can contribute to the PIC fix shutting your unit down. If the install is faulty the PIC can act the same way. If the resistance value on the 'J' line is too low the PIC will shut down right from the get go as well. But you don’t want it to be too high or the PIC fix won’t do its job. The value needs to be just high enough to turn on the v12 with out error.

I would suggest you contact the installer of your v12 and let him know your problem.

Well I guess I will..
Thanks for your help