|
#1
25-01-2004, 17:34
|
||||
|
||||
|
Swapping fan motors
Hey I got an idea but not to sure how to go about it. All right, I want to stick an 80mm four LED case fan in my XBox. So just kinda looking around eBay for the biggest bang for my buck and ran across Thermaltake’s Smart II fan.
I run these fans on my PC case and one ontop of the CPU heatsink and they kick ass. I know some one here at X-S has put one of these fans in my XBox all ready. I really like this fan since it has a nice sensor on it witch can be hooked up in a way that it detects the CPUs heat and spins accordingly to cool it. Thus it will only make enough noise as it has to, to keep every thing cool and no be buzzing at 48 dBA all the time. Any way… So than I got an idea. Why not to do the best of both worlds? Have the LED fan, but with the Thermaltake’s capabilitys. Just swap the LED’s fan motor with the Thermaltake’s motor and it will still be lit and have the heat sensor. Okay so now that I got all that outa the way. How hard would it be to swap the motors? Seems like a simple idea but I’m kinda flying blind on how to go about it. I wouldn’t think there would be a problem with the motor fitting, since they are all more or less the same size. Any advise or idea’s would be welcomed.
__________________
[SIZE=1]NTSC Ver1.0 XBox w/ [URL=http://www.gameshopusa.com/]X2.3 Lite[/URL] flashed with X2 4981.06 120GB WD 7200RPM 8mg cache Samsung SDG-605B * All stuffed in a beautiful translucent green case UK PAL Ver1.4 XBox ([i]not chipped yet[/i]) Stock 8gb WD Philips 6035/21 * All stuffed in a beautiful Crystal Clear case[/SIZE] [I]Having a BMW that says “Made in the USA” is like having a Rolls-Royce that says “Made in Japan”[/I] 
|
| Sponsored Links |
|
#2
25-01-2004, 17:40
|
||||
|
||||
|
Ok I know you would have to be exact on the fitting, because any wobble would lower the fans effectiveness.
Tyler!
__________________
[B]V7 Ps2 Messiah 2 V13 PSTwo DMS4 Pro and HD-Connect(Installed myself)[/B]
|
|
#3
25-01-2004, 19:41
|
||||
|
||||
|
hmm, probably easier to just put the led's on the fan you want to use. Unless you wanted the clear case. I dunno, seems like alot of work to me, but maybe that's the fun part?
Either way, i'd like to see pics at the finished product. 
__________________
--v1.0 [COLOR=Gray]case modded[/COLOR] Xbox with a [COLOR=DarkGreen]160gb[/COLOR] HDD upgrade[URL="irc://irc.efnet.net/fileforums"] [/URL]
|
|
#4
25-01-2004, 20:25
|
||||
|
||||
|
I took a normal case fan apart not to long ago. The blades were easy to get off. The back popped off and a shaft was held in place by an eclip looking thing. The motor it seems seems to be glued down tight.
 As for just putting LEDs in the normal fan, it wouldn’t look as nice as the clear ones. If I can’t change motors maybe I can change the fan blades. I just hope the shafts that the blades are connected to are the same size or else I’m SOL for this idea. Than I can simply add LEDs to the fan. Any way, Tyler you gonna have to FedEx my your digital so I can show Quall pics if I can do this.
__________________
[SIZE=1]NTSC Ver1.0 XBox w/ [URL=http://www.gameshopusa.com/]X2.3 Lite[/URL] flashed with X2 4981.06 120GB WD 7200RPM 8mg cache Samsung SDG-605B * All stuffed in a beautiful translucent green case UK PAL Ver1.4 XBox ([i]not chipped yet[/i]) Stock 8gb WD Philips 6035/21 * All stuffed in a beautiful Crystal Clear case[/SIZE] [I]Having a BMW that says “Made in the USA” is like having a Rolls-Royce that says “Made in Japan”[/I] Last edited by rms2001; 25-01-2004 at 20:28.
|
|
#5
26-01-2004, 06:38
|
||||
|
||||
|
Quote:
Yeah thats gonna happen. Tyler!
__________________
[B]V7 Ps2 Messiah 2 V13 PSTwo DMS4 Pro and HD-Connect(Installed myself)[/B]
|
 |
|
|
Linear Mode
