|
#1
10-11-2003, 15:53
|
|||
|
|||
|
Any Self-Install Tips for a DMS3
I would love it if anyone could provide some posts of their experiences with any soldering-required installs they have done in the past.
I am waiting for my DMS to arrive. Any hints or tips (tools, methods, cautions, etc) that will help be prepare would be mucho appreciated. If this info is already available on this forum somewhere, I apologize for posting this. If you could link me to it, that would be great. I think I'll cut down on the caffeine for the next few days to let my hands steady up a bit! Thanks in advance... --------------------------------- redgamma 
|
| Sponsored Links |
|
#2
10-11-2003, 16:30
|
||||
|
||||
|
if im not mistaken, charlie ps2 may be able to guide you in the right direction if you can catch him online. he has good recommendations from previous members on this subject.
if not him, tyler or bighap may be able to help. hope you get it working. good luck. sorry i couldnt be much help though.
|
|
#3
10-11-2003, 17:32
|
||||
|
||||
|
15 to 18 watt iron, low meltin point solder, 0.10 tip a steady hand,a jewellers eye glass or a 8x magnifying glass.good light .no kids
 take it slow if it your first time,muti meter for checking bridge just in case if any one whats to add to my be i forgot something ohhh yeah and ps2  fibreglass pen for cleaning the mobo where your going to solder
Last edited by jackdor; 10-11-2003 at 17:34.
|
|
#4
10-11-2003, 18:27
|
||||
|
||||
|
Quote:
Last edited by jackdor; 10-11-2003 at 18:31.
|
|
#5
10-11-2003, 22:21
|
||||
|
||||
|
hey guys, i just wanted to post a reply on here cause i am gonna be facing the same situation in another 2 weeks so i went ahead and posted a reply for the email notes to follow up on what to do when i get mine too. easier than posting a whole new thread on the same subject. thanks for the tips
__________________
[B]may the best of your past, be the worst of your future......:cool: ....[/B]
|
|
#6
11-11-2003, 02:58
|
|||
|
|||
|
<- jackdor ->
it IS a v9...cr@p! does the modchip not come with the appropriate wiring? anyone else care to shed some light on which wiring to get for a ps2 v9 running the newest dms3 for v9's? ------------------------------ redgamma
|
|
#7
11-11-2003, 03:34
|
||||
|
||||
|
hey redgamma, i did a little homework on it real quick and came up with a slew of web sites on this subject. check it out.....
type in the ask question field, "ps2 modchip installation tips on soldering". http://www.ask.com
__________________
[B]may the best of your past, be the worst of your future......:cool: ....[/B]
|
|
#8
11-11-2003, 04:24
|
||||
|
||||
|
Basically the problem with fitting to a version 9 is that some of the wires need to go to Vias on the motherboard. These are smaller than the solder pads on the version 5,6 and 7. The alternative is to solder directly to chiplegs which is a bit of a nightmare.
However, take your time ( like put aside a whole day to do it ), an you'll be fine. The first mod install I did was a Messiah 1 an it took me about 5 hours. Now I can get an M2 in in about an hour (Yep, still slow, I know). My m8 who does it for a living can get one done in half that time..... but we all started slow. To be really honest, if you've got any doubt then get an installer to do it for you. I'm lucky that I've got access to professional surface mount soldering kit but have done one at home with magnifier an smally soldering iron. Ottos top tip is use liquid flux.....LOADS OF IT!!!!!!!!!!!!!!!! Top tip two is always use Kynar insulated awg30 wire for all connections except the 3.5Volt line and the ground. Use something slightly thicker for that. I installed an M2 into a version 4 console about 10 times and couldn't get it to run ps2 backups, PS1 backups booted fine, so after ripping my hair out an having a breakdown I tried using the recommended wire rather than any old cheap thin wire an it worked perfectly first time. It does make a big difference what wire you use. Final comment: turn the clockwire into a twisted pair i.e run the wire and run a second wire connected from ground on the chip board to a groundpoint on the ps2 ( I use the gold edge around the motherboard) and twist em together. This puts a sipble shield around the clockwire an reduces the chance of emc problems on the clockwire. Regards
__________________
Zap Brannigan quote - "You remind me of a younger me Fry, Not much younger mind, perhaps even a little older." Last edited by ottoman; 11-11-2003 at 04:39.
|
|
#9
11-11-2003, 09:41
|
||||
|
||||
|
dude whats flux spray?
i used the flux paste to clean the end of my soldering iron why do u need to spray in onto the motherboard
|
|
#11
11-11-2003, 10:21
|
||||
|
||||
|
hey jackdor your mr fixit arnt ya
yeah i used flux paste it cleans the iron as well as makes a good connectionm you dont wanna get a dry joint now do ya
|
|
#13
11-11-2003, 10:57
|
||||
|
||||
|
Yeah I figured that out right away. Anyways, as long as ol jack keeps his cool I wont have to get Empire to ban his local like he did with Zedy.
Tyler!
__________________
[B]V7 Ps2 Messiah 2 V13 PSTwo DMS4 Pro and HD-Connect(Installed myself)[/B]
|
|
#14
11-11-2003, 11:12
|
||||
|
||||
|
Quote:
|
|
#15
11-11-2003, 11:57
|
||||
|
||||
|
Sure, as long as there are no more silly PM's your doing fine.
Tyler!
__________________
[B]V7 Ps2 Messiah 2 V13 PSTwo DMS4 Pro and HD-Connect(Installed myself)[/B]
|
 |
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Linear Mode
