ninja mod

[StartingLine]

how good is the ninja mod..
i am thinking of chipping my console with it..
i already have a lot of backups..

and after chipping it..
it´s is necesary to ad just laser or just by using good media
i can play my games...

by the way..
i can plary RE4 with it?

[Technitian3]

Ninjamod is an ok chip, but there is little info on the Nm website. I had to search hi and lo to find a wiring diagram for a ver.C cube, and without a broadband adaptor it is practically useless as original bios have trouble reading ANYTHING. Upload updated bios (ver. 1.4, autoboot bios2 disabled!!!) via BBA and it will read decent +/-R media.
When installing the chip I recommend lifting the one leg on the orig. bios chip, otherwise none of your settings (NTSC/PAL, IP adresses,...) can be saved. Not a big deal on a PAL cube, as the chip defaults to PAL, but a rolling black and white screen every time you turn it on (NTSC cube) gets annoying. I have made more coasters for the 'cube than for my xbox and ps2 combined, but I've only had it a month and am still figuring out what works.
Some useful tools for GC backups are "fstfix gui" and "GCM utility" because, as stupid as this sounds, some GC iso's will only work if you convert them to a GCM file and remove the garbage that pads them up to 1.4 GB (GCM utility), then wipe the image and put back all the padding (fstfix) and burn using Nero.
BTW, R.E.4 works flawlessly, but some games that stream the audio will have issues (audio only), but fstfix can remedy that.
P.S. some of my burns wont go past the loading screen, so I'm gonna tweak the laser to see if it helps, will post my results.
One more note: rename GCM files to iso, then they can be burned.

Laser tweak didnt/wont help, at least in my case. Cube is new enough that POT was well within proper operating range.

[sober2005]

please help me, i have my GameCube ripped apart and i'm finding the pictures in the instructions are way-way-way different than the motherboard i found in my GameCube. OK, but nowhere did it say that the Ninja Mod was only compatible with certain versions of GameCubes ... so i assumed. i didn't do an insane amount of research but i really don't know much about this stuff ok? ... it's not easy to find information on the web and i searched for hours so don't say i'm lazy. i have no clue what version my gamecube is or even how to find out. i purchased it recently ... maybe 6 months ago. does anyone have any way to find out if i can actually install the Ninja Mod?

[sober2005]

ok, never mind what i wrote before ... my version is C and i found pictures online to show me how to do it ... but the Pin that must be lifted on the BIOS ... is this impossible? ... i don't get what "lifting it" means as i'm not a circuit board guy. i attached a wire to it and then pulled ... and the wire broke off ... the pin on the BIOS didn't move. i tried using a fine-tipped knife ... nothing happened. what is this pin supposed to do? ... must i lift it up? ... ... help!

[Technitian3]

You dont have to lift the leg, but as you have a NTSC 'cube you will want to. The ninja modchip defaults to PAL, and without lifting the leg you cannot save your settings. This means every time you fire up your 'cube you will be greeted by a rolling black and white screen. What worked for me was taking a large safety pin and bending the very tip of it over (about the width of the bios leg), then, with the pin hooked under the leg, apply heat (15 watt soldering iron) to the leg and simultaneously pull on the pin (pull parallel to the motherboard, not straight up, as you risk breaking the leg off that way). The pin should slip under the leg, breaking the connection to the board. Once accomplished, gingerly lift the leg a little more and make your connection.

[StartingLine]

and what about the viper?
would that be a better mod?
is there anby king of mod that can play pal and ntsc games

[lucecomputers.com]

Originally Posted by sober2005

ok, never mind what i wrote before ... my version is C and i found pictures online to show me how to do it ... but the Pin that must be lifted on the BIOS ... is this impossible? ... i don't get what "lifting it" means as i'm not a circuit board guy. i attached a wire to it and then pulled ... and the wire broke off ... the pin on the BIOS didn't move. i tried using a fine-tipped knife ... nothing happened. what is this pin supposed to do? ... must i lift it up? ... ... help!

Can you please list this picture or post it? I have the same issue (version C board, with no directions) and I am unable to find a contact point for wire 'E', as there is no FIL34 contact spot.


Thanks in advance for your help!
Kyle