x box booting then shutting down

bnke · #1 09-03-2004, 19:57

i just got done instaalling an alladin 64 in my x box .i followed all the photos and it took me 45 min to find the do point and another half hr to get it stuck cleanly besides every time i moved it anyway do i need to use pogo pins with the alladin if so where do i get them an is this why it boots and then shuts down .i have not installed evox on the hard drive yet .i wanted to make sure everything was working . it was a very clean an nice job i thought and what would make the tutorials even nice would show an install of the alladin any suggestions would be very appreciated. faqing x box . when i get it working ill leave a picture of an install im sure it would help a lot of people out thanks bnke1

AXmichigan · #2 10-03-2004, 11:44

did it do three reboots then flash red/green?

bnke · #3 10-03-2004, 15:36

no when it stops i have to restart does not reboot by itself .itried restarting 3 times manually but still nothing

AXmichigan · #4 10-03-2004, 16:04

when u first boot what happens?

bnke · #5 10-03-2004, 17:33

starts out fine i get a green light if i hold pwr button tray opens if i hold reset button as long as i hold it is yellow im playing abes worls or munches odysee goes about to where he gets snagged by his foot then shuts down .no lights just shuts down. if i restart it does not go as far as the first time but shuts down sooner . i have not installed evox on the hard drive yet . should i pull the alladin out and look for pogo pins .looks fine no crosses

bnke · #6 12-03-2004, 01:04

im getting the executor2 tm on tv under ms

but still shutting down after a few minutes seems like it takes less an less time to shut down tho 2

Quall999 · #7 12-03-2004, 06:04

the xecuter2 are the bios; normal. I suggest you look at their chip install. If there is an activate/deactivate way of using the chip by pressing the eject button, or the power on (one boots with the chip, the other boots the xbox normally). I suggest to disconnect it and make a switch instead.

edit: omg, i spelled it executer

bnke · #8 12-03-2004, 16:55

alladin64

i just installed an alladin 64 chip in my x box . i have not installed evolx on the hd yet when i start up under the x i recieve xecutor2 so it seems the chip is being recognised .the game will start and after a few minutes my x box is shutting down .i have no idea why hopefully i didnt screw anything up. made my own pogo pins with wire. all connections look clean only possibility could be 1 of the traces was scratched .but they all look intact.can some1 please help. also chip was suppose to be flashed allready with 4980 bios only green flashing light so far then solid. also seems as when i press pwr button it is not shutting off but opening the tray . power button not working should i remove L2.any suggestions would be greatly appreciated
you think its one of the wires. active an deactivate supposeto woek with reset according to alladinchip.com.where between would i place a switch.

Quall999 · #9 13-03-2004, 03:43

My switch is just poping out the back of the xbox. In the corner where the fan is located, there is a small hole that you can fit wires through if you don't want to cut the casing.

and if the power button does not work, then it is the chip doing that. I suggest you remove those wires.

bnke · #10 13-03-2004, 21:05

now im getting no green light on pwr one flash of yellow then black and box is still shutting down i think you were rt it was the wires r3g3 got tangled and fell off .went out an bought 30 wire redid r2 an r3 an do left 26 awg on 2 .seems like i might of lost do cause im not getting executor tm no more only ms tm an box is still shutting down shoulda bought a box allready done .i aint even gonna attempt playstation2 i gotta few messiah chips an alladin chips lol . an they better be drop proof no skinmping on the do.e mail me