D0
 

Hey,

i am just wondering if this d0 is preped enough i will attach the picture later.

Oh and can i have some soldering tips.

here are the links

http://homepage.ntlworld.com/teresa....m/DSC00190.JPG
http://homepage.ntlworld.com/teresa....m/DSC00198.JPG
http://homepage.ntlworld.com/teresa....m/DSC00201.JPG
http://homepage.ntlworld.com/teresa....m/DSC00202.JPG

thanks
seaneyb

hehe
u just replied to urself

yea,
take a look at the pics and zoom in to the d0 point and see if its all ok

those pics kinda suck..
can u get better ones?
try takin the flash off

ohhh there good ones.

i try but its a pain keep undoing the xbox.but dcs201.jpeg you can see the d0 point fine.

Hello can someone tell me if the d0 point is preped enough?

how can i solder onto this git!

dude calm down
u ask soo many of the same questions
just give it a shot

yea
i dont rely on the top d0.

give it a shot and let us noe how it goes

im gonna do the bottom d0 next week sometime i got to get lots of equipment wire solder flux desoldering braid tip cleaner! wire strippers!
hehe anyone know where i can get cheap wire stripers i seen em but there very expensive.

The top D0 looks fine. Its not as hard to solder to as people make it out to be.

What I've found when I do X2 installs is the D0 wire is just small enough to fit in the D0 hole it self. Put the wire in the hole and heat it up. Since the wires are pre-tinned the soldering iron heats that up and the solder flows into the hole making good contact.

hey,

what chip you reccomend me getting then? a duo or a x2 lite?

o my god
come on seaney... dammit!
just go with an xbit or an x2
its been sooo long already

no ive been told not to get a xbit or any non solder as they move easily and now i got a soldering iron i think i can do a proper job!

X2 all the way. Easy to install, easy to work with, and easy to upgrade later.

yea i like the way u solder the wires on buttttt i wanna use the underside d0 point that is not possiable without the pinheader install.

on the other hand duo looks easy and is alot cheaper!

Who says you cant solder to the ALT D0 if you do a wire install? The XBox dose not care. Who ever told you that is full of it.

I use to do the ALT D0 when I installed chips before I got brave and started doing the top D0. It works fine with wire installs.

ok what should i do extend the wire i dont think it will fit round the mobo?

i donno what to get now. i think i will stick with the duo x.

You will only need to extend the wire if you have a v1.0 board and the LPCs are fulled. Other than that the D0 wire fits nicely thru an open LPC and is long enough.

yea i know i got a v1 u know the holes filled with solder all i need to do is touch the lpc holes and dunk in the wire? and then it makes a good bond yea?


or i could desolder a hole? nah it could damage it i think but still i could extend. i donno man look what u done im in 2 minds to get a duo x or a x2 lite????

Ya, 1.0s are easy to mod. Just heat the solder up and when you see its hot push the wire in and pull your soldering iron away.

Its not really hard to extent the D0 wire. Most people use the other D0 wire thats used for header pin installs. Solder the two ends together and tape them or use heat-shrink to insulate them.

okies im still debating if i should get a x2 or a duox i donno i heard that the duo x is superiour to the x2 i think i get the duox caus of the booting procidures

I'd go with what ever one you fell is better. I my self like the X2, never even herd of the duo x.

I like the fact the X2 has external switches for on / off, bank 1 & 2, and a BIOS protect. Even an LED that tells you if the chip is on or off.

www.duomodchip.com i got the duo chip in my ps2 and its v good and ive heard duo x was good as well www.ukmodchips.biz

Duo-X is a fantastic chip. It's no surprise that some peeps havn't heard of it cos its brand new.

Its the easiest xbox mod to fit and the easiest to disable for xbox live. The sexi blue LED (gimmick) tells you straight away that your install is good.

To enable the chip, boot up with the reset button (no need to long press like the Aladdin) & to disable the chip, boot with the eject button instead. With the chip enabled, the xbox logo is blue.

Within a month of the Duo-X arriving in the UK, X2 prices have dropped by a third.............. what does that tell you?

well spoken hull chipper!

i will buy the duox which is a bargin price. I need some flux and tip cleaner but i dont have a credit card? does anywhere sell it ive been too homebase and my local diy store and all they sold was solder!

Dude, you seem like a top bloke but it's getting me down seeing you post again, and again, and again.

I will mod your xbox for free with a Xbit if it'l keep you happy!

I've realised that for the last week I come on here to see seaney's new posts and it's driving me crazy! :p




(No offence dude! :rolleyes: )

okies when u send me a xbit?:D

pay for it and i'l install it for free :D

I have to say though you are one hell of a character!

i could install it matie lol. i wanna get a duo x. which i prob get.

yea i get a duo x soz dude. its cheap.